Skip to content
VETCNCCNC MANUFACTURING
Stepped metal shaft, flanged hub and open pocketed housing

Nickel 200 and 201
CNC Machining

Compare Nickel References

Machined Pure-Nickel Components and Contact Features

6 component types

Flanged sleeves

A sleeve connects its bore, outside seat and flange face. The cylindrical contacts locate the adjoining part while the flange establishes axial position; those working references remain related through machining.

Contact and mounting plates

A plate combines a defined contact face with fixing holes, slots or local recesses. We machine the contact region and attachment geometry together without extending the same finish requirement to every exterior surface.

Threaded adapters

A hollow adapter joins its two specified interfaces through an open passage. The retaining thread, seating surface and wrenching region have separate roles within that connection.

Stepped stems and pins

A stem can combine round seats, axial stops and a driving or retaining feature. Turning establishes the connected diameters; local flats or cross-features remain tied to the working axis.

Ported component bodies

A body brings an accessible passage to a seat or adjoining component. The bore intersection, mounting reference and retained section determine how its local features can be cut and finished.

Rings, discs and spacers

A ring or disc establishes a local gap or bearing contact within the selected assembly. The actual seating faces define its useful thickness, separately from an outside edge used only for handling.

We quote custom turning, milling and associated feature work in the specified commercially pure nickel product. Nickel 200 / UNS N02200 and Nickel 201 / UNS N02201 are distinct from Inconel, Hastelloy and nickel-plated steel; the accepted stock definition stays with the finished component.

Nickel 200, Nickel 201 and the Ordered Stock Condition

Nickel 200 / UNS N02200

Nickel 200 is commercially pure wrought nickel. The ordered material specification identifies its chemistry rather than treating every pure-nickel description as the same purity level. Our reference comparison below retains the particular VDM product data.[1]

Selection focus
Named grade and product specification

Nickel 201 / UNS N02201

Nickel 201 is the low-carbon alternative within this pure-nickel pair. Carbon control matters where the component’s thermal history makes that distinction important; the grade remains part of the released material definition.[1]

Selection focus
Carbon-controlled material selection

Annealed or work-hardened condition

Material condition changes chip behavior and the retained mechanical properties. A route chosen for an annealed blank is not inherited unchanged by a cold-worked product. The accepted incoming and delivered states stay explicit.[2]

Selection focus
Actual condition through manufacture

Rod, plate and suitable near-net blanks

Round stock can suit sleeves and stems; plate can suit contact pieces and ported bodies. The usable envelope includes the section left around bores and shoulders. A shaped blank saves removal only where it leaves material at the finished contacts.

Selection focus
Product form and machining allowance
Round stock with a retained machining allowance
Flat stock with a part outline inside the usable plate section

Use one named reference rather than mix producer limits

The table uses VDM’s March 2022 Nickel 200/201 sheet for a consistent chemical and physical comparison. Its figures retain their conditions; they are distinct from the purchased material certificate and the dimensions of the machined part.[1]

The stock product, condition and final acceptance remain linked to the component drawing.

VDM Nickel 200 and 201: selected named references
PropertyVDM Nickel 200VDM Nickel 201Reference basis
Nickel content≥99.2 wt%≥99.2 wt%Named producer chemistry
Carbon limit≤0.10 wt%≤0.02 wt%Named producer chemistry
Density8.9 g/cm³8.9 g/cm³20°C
Thermal conductivity71 W/(m·K)79 W/(m·K)Typical; 20°C
Electrical resistivity9 µΩ·cm9 µΩ·cmTypical; 20°C
Elastic modulus205 GPa205 GPaTypical; 20°C
Curie temperature360°C360°CProducer physical reference

VDM material data sheet 1101 Rev. 02, March 2022, pages 3–4. These are named product-reference values and conditions. Other producers or governing purchase specifications may use different chemistry limits; they are not combined into this comparison.

Turning and Milling Commercially Pure Nickel

Cutting direction below an altered surface layer with support beneath the workpiece

Cut beneath the altered surface

A rubbing pass can leave a work-hardened surface for the next cut. VDM’s machining guidance calls for a meaningful cut beneath that affected zone. The route maintains useful cutting engagement rather than relying on repeated light rubbing passes.[2]

Manage material flow at the edge

Pure nickel can flow around the cutting edge and produce long chips. Special Metals discusses this behavior separately from the high-strength superalloys. Tool condition, chip exit and the actual stock state affect the finished edge and surface.

Support the retained geometry

A soft, thin flange or sleeve can move under the holding load. We use suitable robust contacts and keep the released component geometry distinct from the shape imposed while it is clamped.

Seats, Working Contacts and the Delivered Condition

Working boreEnd seatContact faceMating componentRetained wallAccepted condition
Each interface has its own reference and acceptance
Finished nickel features and their accepted condition
FeatureWorking requirementAccepted conditionVerification
Sleeve or adapterBore, outside seat and shoulder relationshipAfter included final operationsSize, form and specified datums
Contact plateWorking face and attachment geometryDefined free or supported stateFace and related fixing features
Stem or pinConnected diameters, stop and local featureSpecified material and delivery stateAxis and working-length relationships
Port or thin sectionPassage, retained wall and edge conditionFinished component with defined accessSelected geometry and internal-edge checks

Dimensional limits follow the released component drawing. Any required material-property or assembled-function acceptance is defined separately from these geometric checks.

Finish and Accept the Intended Nickel Interfaces

We connect the part’s bore, seat and attachment geometry in the machining route and inspect the finished condition specified for those contacts.

Geometry for Pure-Nickel Component Manufacture

Keep a useful holding region

A robust outside land or sacrificial stock region can support a thin finished feature. Removing every holding surface too early can add another setup or leave an unstable final cut.

Make the internal edge reachable

A side bore can meet the main passage behind the visible opening. Its position and access determine whether the intersection can be finished without disturbing the adjacent working seat.

Separate contact land from clearance

A local recess can clear a fastener or adjacent part while retaining the intended load-bearing area. That distinction avoids cutting away a useful contact merely to match the overall appearance.

Retain material at a shoulder

An undercut, deep groove or large bore uses the section beside a shoulder. Its root and remaining wall follow the released mechanical geometry rather than an assumed minimum for every nickel component.

Discuss Part Requirements

Where a Pure-Nickel Machined Interface Can Be Useful

Electrical contact and conductor pieces

A plate, disc or terminal body can provide the geometry of a defined current path. Its attachment and mating face remain part of the electrical assembly design; bulk material properties do not specify every contact in that path.

Local thermal contacts

A machined face can connect a component to a receiving thermal interface. The selected contact area and installed arrangement accompany the material choice instead of being replaced by a single conductivity figure.

Components for process equipment

A sleeve, adapter or ported body can serve a released process-equipment design. The specified nickel grade follows that equipment’s actual chemical and thermal conditions rather than a general corrosion-resistant label.

Instrument and mechanism interfaces

A spacer, stem or mounting piece establishes a position within the instrument or mechanism. The component supply covers its drawing-defined geometry and agreed finished state.

Working Surfaces, Edges and Nickel-Part Handling

Defined contact land separated from a relieved surrounding face

Controlled contact texture

We retain the required texture and form at a bore, seat or contact face. A separate cosmetic finish on the exterior need not extend into a fitted or electrically active region.

Useful edges after deburring

Removing a raised lip should preserve the end length, land width and entry geometry. A narrow contact can be lost through excessive rounding even when the edge looks smoother.

The specified clean delivery

Cleaning follows the next use and the ordered acceptance. A component intended for later heat or joining work retains the preparation required by that route, separately from its visible appearance.

Protect and identify similar parts

Packing separates working faces from rubbing or impact. Part, grade, condition and batch identity remain connected so similar-looking nickel components are not substituted during assembly.

Material Identity and Finished-Feature Records

Sleeve inspection references linking its working bore, shoulder and end seat

Keep the actual material identity

The stock record identifies the purchased UNS grade, product and condition. A general producer sheet supports selection; it does not identify the particular material used for the order.

Check the completed mating features

Bore, shoulder, contact face and mounting details are measured from their specified references after the included final operations. A held thin part is accepted in its defined released or supported state.

Separate geometric and functional results

The component’s dimensional record covers the agreed features. Electrical, chemical, load or assembled-performance requirements need their own acceptance when they form part of the order.

What Changes Nickel 200 or 201 Machining Cost?

Stock form and material utilization

A round blank can reduce preparation for a sleeve, while a flat blank can reduce removal for a contact plate. The usable shape and supply condition affect the complete route, not just the material weight.

Cutting route and access

Long passages, interrupted contacts and secondary faces add tool directions and handling. A fragile flange or narrow remaining wall can require extra support through the final operations.

Final contacts and records

A selected surface finish, controlled fit or recorded measurement adds work where it is required. Keeping those requirements on the working regions avoids extending the same operation over every exterior face.

Quantity and shared preparation

Programming, fixture preparation and first-part checks are shared across an unchanged batch. A changed stock condition, contact or finish can require new preparation even when the outside shape appears similar.

From a Defined Nickel Blank to Repeat Components

Release grade, stock and geometry together

The approved component connects its UNS identity, supplied condition, product form and finished interface drawing.

Establish the first contact features

Initial parts establish the locating route, support and access needed to produce the specified final contacts. Included fit checks use the intended mating geometry.

Repeat the accepted definition

Programs, locating references and included finishing follow the released part revision. A material or interface change remains identifiable in the repeat order.

Protect the delivered condition

The packed batch preserves accepted faces and carries its part and material identity into receiving and assembly.

Nickel 200 and 201 CNC Machining FAQs

Why is Nickel 201 considered for sustained service above about 315°C?

Special Metals links its lower carbon limit to avoiding graphite-related grain-boundary embrittlement during extended exposure, provided carbonaceous material is not in contact. That explains the grade preference, while a complete part temperature rating follows the stress, exposure and product requirement in the equipment design. Stress, exposure and the actual product requirement remain part of the equipment design.

Does an austenitic structure make pure nickel nonmagnetic?

No. A crystal-structure description is not a nonmagnetic-material specification. VDM identifies these pure-nickel grades as ferromagnetic. A component intended near a magnetic field or sensitive instrument therefore needs the applicable magnetic requirement in addition to its ordinary dimensions.

Is nickel-plated steel equivalent to a part machined from Nickel 200?

No. A plated part retains its underlying steel body, while Nickel 200 identifies the bulk material of the machined component. Cutting through the coating also exposes that substrate. Material, section and service definition are read from the stock record for the machined component.

Does resistance to caustic solutions establish suitability for an oxidizing acid?

No. The solution and its condition matter. VDM distinguishes concentration, temperature and aeration and warns of attack in oxidizing salt solutions. A material selected for a particular alkaline process cannot be approved for another chemical duty from the general nickel description alone.

Can a visually clean part go straight into a later heating operation?

Visible appearance is insufficient. VDM warns that contamination from marking products, lubricants and low-melting substances can damage nickel during heating. The required preparation must suit the later process; the machining order identifies that downstream need rather than equating a bright finish with suitable thermal-process cleanliness.

Does the material resistivity alone establish the resistance of a contact component?

No. For a uniform bulk path, R = ρL/A. Using ρ = 0.09 µΩ·m, L = 10 mm and A = 10 mm² gives 0.09 mΩ. The path geometry therefore matters alongside the material value. Mating contacts add their own interface resistance, so the complete assembled connection is measured as built.

PROJECT SUPPORT

Discuss Your Nickel 200 or 201 Component

Send the component drawing, exact material specification and condition with the quantity. Identify the working contacts, final surface and acceptance required for the quotation.

Commercially Pure Nickel References

Named material data, stock-condition and thermal-service guidance used for the specific distinctions on this page.

  1. VDM Metals — Nickel 200 and 201, March 2022Named chemical and physical properties, tables 2a/2b and 3a/3b.
  2. VDM Metals — Fabrication and Heat TreatmentStock condition, work hardening and preparation before later heating, pages 8–10.
  3. Special Metals — Nickel 200 & 201Chip behavior, product conditions and low-carbon material guidance for sustained elevated-temperature service.
  4. Electrical-resistance calculationBulk resistance follows R = resistivity × path length / cross-section; actual contacts add their own interface effects.
VETCNCCNC MANUFACTURING

Get a Quote

Upload Drawing

*Required fields

Acetal part geometry illustration

Enlarged part geometry illustration

AI-generated part illustration.

English
WhatsApp Email us

Tell us about your project

Share your requirements and we will get back to you by email.

PDF, CAD or ZIP · up to 20 MB