Skip to content
VETCNCCNC MANUFACTURING
Silver open channel, hollow enclosure section and slotted mounting rail

Slot and Groove Machining Services

We machine straight and curved slots, keyseats and annular grooves in custom metal and plastic parts. The feature may guide movement, locate a drive key, seat a seal or retain a ring. We relate its width, depth and position to that job and preserve the surrounding contact surfaces.

  • Open and closed slots
  • Keyways and ring grooves
  • Defined contact surfaces

Parts with guiding, sealing and retention grooves

A slot can provide movement or a fixed drive connection; a groove can support a seal or retaining element. We machine the local feature together with the surfaces that locate the component.

Silver mounting plate with two elongated slots and surrounding fixing holes

Slotted mounting plates

Elongated openings give a mounting bolt an adjustment path. We machine the slot length and width with the clamping face and remaining edge material, so adjustment does not remove the surface that carries the fastener load.

  • Adjustment travel
  • Clamping faces
  • Retained edge material
Discuss a slotted plate
White polymer guide block with an open straight channel and four mounting holes

Open-channel guide blocks

An open channel locates a moving strip, rail or mating block. Its opposed walls and floor define the guide; entry relief and surrounding fixing holes let that feature work within the assembled support.

  • Opposed guide walls
  • Channel floor
  • Mounting relationship
Discuss a guide block
Metal hub with an open central bore and a rectangular internal keyway at its mouth

Keyed hubs and sleeves

A hub keyway must remain related to the bore and mating shaft key. We treat the internal slot as part of the drive interface, including its accessible end and the material remaining around the bore.

  • Internal keyways
  • Bore relationship
  • Drive interfaces
Discuss a keyed hub
Metal cap with a wrench boss, threaded skirt and a circumferential seal groove

Seal-grooved caps and bodies

A seal groove works with an adjacent land and a mating bore or face. We retain that relationship while machining the cap, cover or body, including the entry edge that the seal passes during assembly.

  • Seal grooves
  • Adjacent lands
  • Assembly edges
Discuss a seal groove
Yellow-brown polymer ring with an open bore and a shallow external circumferential groove

Grooved polymer rings

A shallow circumferential groove can locate a ring, cover or mating insert. The remaining wall and supported machining state matter when a compliant polymer part is released from its fixture.

  • Circumferential features
  • Remaining wall
  • Released condition
Discuss a polymer ring
Metal locating block with a V-shaped channel and two fixing ears

V-groove locating blocks

Angled contact faces locate round work or a mating profile. Their included geometry and position relate to the mounting base; the groove is not defined by a top opening width alone.

  • Angled contact faces
  • Base relationship
  • Locating geometry
Discuss a locating block

Milled slots, turned grooves and internal keyseats

The route follows the feature orientation, available access and blank condition. Open-face milling, annular turning and internal slot work solve different geometries.CNC turning can produce an annular groove together with its bore, journal and shoulder on a suitable rotating part.

Accessible straight and curved slots

We mill slots from an accessible face, retaining the specified path and end form. A closed slot requires an entry route within the opening; an open slot allows approach from its end. Sandvik Coromant distinguishes these access conditions in its slot-milling guidance.

Path • entry • end form

Annular sealing and retaining grooves

Circumferential grooves relate axial location, root diameter and width to the neighboring bore or shaft surface. On a body that cannot rotate, accessible circular milling can provide a different route from turning.

Axial position • root • land

Internal keyseats and restricted features

An internal keyway or undercut needs room for the tool to reach and leave the working surface. We define the appropriate slotting or secondary route for the particular opening rather than promise every blind or hardened feature from a standard end-milling setup.

Internal access • exit • secondary route

Width, end form and the material around a groove

A nominal slot width describes only one part of the geometry. Its location, bottom and accessible ends determine whether the mating feature can enter and work.

Closed-slot plan and section separating width, end radius, depth and remaining material
Separate the plan-view end radius, section depth and datum-related location.

Location relative to the working surfaces

We relate a guide slot to its mounting base, a keyseat to its shaft axis and a seal groove to its mating diameter or face. Measuring from an unfinished outer edge can leave the functional relationship uncontrolled. Connected faces and mounting features can be included in the same CNC milling route when their datum relationship and tool access allow it.

Closed ends and bottom shape

A rotating cutter leaves a plan-view radius at a closed end. The mating tongue, key or fastener needs the intended clearance there. A flat floor, corner relief and an undercut are distinct geometry requirements, not automatic consequences of specifying slot width.

Support beside deep or narrow features

Removing material can leave a flexible wall or narrow lip beside the groove. We keep useful support during cutting and inspect the relevant released condition so fixture pressure does not conceal movement.

Working lands and assembly access

A groove edge may sit beside a seal land, bearing shoulder or clamping face. We preserve that working surface and the insertion route for the mating element instead of applying the same edge treatment to every opening.

Materials for slotted and grooved components

Hardness affects the cutting route; expansion, stiffness and moisture response affect support and measurement state. The references retain their particular grade and test basis.

Metal reference properties

Metal properties relevant to groove manufacture and measurement
MaterialGrade / conditionReference property
Aluminum6061 extrusionCLTE 23.6 µm/(m·K), 20–100°C
Stainless steel316L / EN 1.4404CLTE 16 µm/(m·K), 20–100°C
Alloy steel42CrMo4 +QT; Ovako 327A, round bar 40 < d < 100 mmHardness 270–320 HB
Brass / copperC36000 / C11000CLTE 20.5 / 16.9 µm/(m·K), 20–300°C / 20–100°C

References: Hydro Alloy 6061; Outokumpu Supra range; Ovako 42CrMo4; Copper Development Association C36000 and C11000. CLTE is the typical coefficient of linear thermal expansion over the stated interval; hardness applies to the stated bar condition and diameter.

Engineering-plastic reference properties

Polymer properties relevant to support and dimensional state
MaterialGrade / testReference property
POM-CTECAFORM AH natural; ISO 527-2, 1 mm/minTensile modulus 2,800 MPa
PA6TECAMID 6 natural; ISO 62, 23°CWater absorption 0.30 / 0.60%, 24 / 96 h
PEEKTECAPEEK natural; ISO 527-2, 1 mm/minTensile modulus 4,200 MPa

Typical values from Ensinger TECAFORM AH natural, TECAMID 6 natural and TECAPEEK natural product data. Modulus: ISO 527-2; water absorption: ISO 62. Stiffness affects support around a groove; moisture response matters when selecting the inspection and service condition.

The selected stock condition stays with the component definition. Material properties inform machining and measurement; they do not prescribe a universal groove tolerance or service load.

Edges, cleanliness and final groove condition

The delivered feature includes the specified treatment without losing the contact geometry that made the groove useful.

Controlled edges beside contact surfaces

We remove loose burrs while retaining the specified corner and land. An uncontrolled chamfer can reduce a retaining shoulder or seal-contact width even though it makes an edge feel smoother.

Cleaning roots and restricted recesses

Narrow roots and undercut regions can retain chips. We provide a cleaning route suited to the accessible geometry and keep inspection of the machined recess separate from any separately required assembly leak or performance test.

Dimensions after coating or treatment

Deposited finish reduces available slot width and changes groove surfaces; material-removing treatment can enlarge them. Allowances, masking or final sizing place the accepted geometry at the required delivered state.

Slot, keyway and groove inspection

Shaft-keyseat section with width and depth references alongside five separate finished-feature checks

We check the feature in relation to its mating surfaces. Slot position, key engagement depth and the form at a closed end are each checked against the mating surfaces.

The inspection route separates size, datum-related location, section geometry and finished edge condition. Access determines which of those can be measured directly.

The selected DIN 6885-1 references below show how shaft diameter, key section and shaft-keyseat depth are connected. They describe parallel-key geometry, not a general sizing rule for seal or retaining-ring grooves.

Separate checks for slots and grooves
FeatureFunctional relationshipInspection basis
Width / wall formClearance or selected mating fitSpecified size limits and controlled wall length
Location / orientationAlignment with base, bore or shaft axisDrawing datums and position / orientation
Depth / root diameterMating engagement or selected groove sectionIdentified depth reference or root diameter
Closed ends / accessInsertion and travel of the mating elementEnd radius, relief and usable length
Edges / final surfacesRetained contact after included treatmentSpecified corner, land and delivered condition

Shaft-keyseat depth and hub-keyway depth are different dimensions. We identify the controlled surface and drawing convention before choosing a depth-measurement reference.

Selected DIN 6885-1 shaft-keyseat references
Shaft diameter d (mm)Key section b × h (mm)Shaft-keyseat depth (mm)
93 × 31.8 +0.1 / 0
135 × 53.0 +0.1 / 0
186 × 63.5 +0.1 / 0
248 × 74.0 +0.2 / 0
3210 × 85.0 +0.2 / 0

Dimensions in millimetres. Selected shaft diameters and associated key sections from Ganter’s DIN 6885-1 extract; shaft-depth upper deviations are shown explicitly. The released drawing specifies the applicable key system and fit. Source: Ganter / Elesa+Ganter DIN 6885-1 technical data.

From a mating-feature trial to repeat parts

A stable route retains the functional reference and treatment state rather than only the nominal cutter size.

First mating-feature parts

First parts establish whether the selected key, sliding element or seal can be installed and whether the controlled surfaces are accessible to inspection. That closes the part’s manufacturing definition before a larger run.

Blanks with retained support

A bar, tube and partly machined body leave different material around the same groove. The preparation route keeps the stock and support conditions relevant to the finished wall or lip.

Repeat variants and revisions

We retain the accepted datum setup and final treatment sequence. A changed groove position or depth can affect a neighboring shoulder, port or fastener even when the outer profile stays the same.

What changes slot and groove machining cost

The removal path, restricted access and final checks explain more than slot count alone.

Length, depth and removal route

A longer or deeper groove adds cutting and chip-removal work. A broad accessible channel and a narrow deep slot need different tool engagement and support, even when their removed volume is similar.

Undercuts and internal access

An accessible face slot can share ordinary part machining. An internal keyway or hidden undercut may require different tooling, an extra setup or a separate process, adding preparation as well as cutting time.

Working surfaces and acceptance

Controlled guide walls, sealing surfaces and datum-related keyseats require suitable finishing and measurement. Coating or heat treatment can add an intermediate and final state to that route.

Order quantity and common preparation

Programming, fixtures and first-part checks are spread across the ordered quantity. A family of matching slots can share preparation; changed fits, blanks or treatments can divide that work again.

A defined machining and delivery sequence

  1. Retain the functional geometry

    We tie slot or groove location, mating surfaces and material condition to the released component revision.

  2. Set the access and treatment route

    The manufacturing definition retains the required end form, secondary operations and final accepted condition.

  3. Machine and inspect the interfaces

    Size, position, depth and surface checks follow the drawing, with the agreed records linked to the part identification.

  4. Protect working edges

    Packing separates exposed grooves and locating surfaces so their accepted edges are not damaged in transit.

Slot and groove machining questions

Are DIN 6885-1 and DIN 6885-2 keyways interchangeable at the same width?

No. Ganter’s technical extract distinguishes their radial key position. Key projection and mating hub depth follow the key system specified for that shaft and hub, alongside the width. The selected shaft and hub must use the intended key system; changing the suffix can change the assembled engagement.

Does nominal key width determine whether the key is fixed or sliding?

No. The shaft and hub width-tolerance zones also determine the seating. Ganter’s extract pairs P9/P9 for a tight fit, JS9/N9 for a loose fit and D10/H9 for a sliding fit, stated as hub/shaft zones. The drawing selects the required relationship rather than relying on the nominal key width alone.

Will a cutter matching the slot width automatically produce accurate parallel walls?

Not necessarily. Sandvik Coromant notes that cutting forces can deflect an end mill in a full-width pass. Its keyway guidance separates roughing with an undersized cutter from wall finishing. The completed width and wall geometry therefore come from the roughing and finishing passes, and a closed slot retains the intended plan-view end radius.

Can a backup ring be added without changing an O-ring groove?

Not automatically. Parker’s O-Ring Handbook provides different gland-width arrangements for seals with one or two backup rings. Their space and pressure-side arrangement belong to the selected sealing design. Adding a ring to an unchanged narrow gland can crowd the assembly rather than improve its support.

Will a stronger retaining ring compensate for a weak groove?

No. Smalley checks both ring shear and groove deformation, with the lower capacity controlling the assembly. A stronger ring does not raise the groove material’s yield strength. The groove section, material and actual loading must remain compatible with the selected retaining element.

Does a satisfactory static thrust check establish a retaining groove’s rotational suitability?

No. A ring on a rotating shaft also has a rotational limit: centrifugal force can expand it and lift it from the groove. Smalley treats that as a separate selection check. The chosen ring and groove arrangement must suit the operating speed, independently of the static thrust result.

PROJECT SUPPORT

Discuss your slotted or grooved part

Send the component drawing and quantity so we can define the feature, its manufacturing access and the required finished state together.

VETCNCCNC MANUFACTURING
English
WhatsApp Email us

Tell us about your project

Share your requirements and we will get back to you by email.

PDF, CAD or ZIP · up to 20 MB