Insulating washers
A turned or profiled washer separates fastened surfaces. Its bore clearance and remaining annulus determine where the clamp force enters the laminate.
A turned or profiled washer separates fastened surfaces. Its bore clearance and remaining annulus determine where the clamp force enters the laminate.
Flanged bushings have connected bore, outer-seat and flange features. A rolled-tube blank and a sleeve cut across flat sheet retain different reinforcement arrangements.
A wear plate combines a running face with recessed fixings. Material beneath the screw head and the edge of the sliding track both remain supported.
Milled supports locate terminals through holes, slots and stand-off faces. The exposed edge and hole spacing form part of the installed electrical path.
A pocketed nest locates the workpiece on selected lands. Relief beside those lands clears unwanted contacts without leaving a thin laminate tongue.
Turned rollers relate a running surface to their axle bore. The drawing distinguishes the running band from the flange and the fastening faces.
We quote custom machined phenolic laminate components, from insulating washers and terminal supports to bushings and wear plates. Paper, canvas and fine-weave linen grades serve different jobs; the resin and reinforcement remain part of the component definition.
Paper-based grades are used for insulating plates, washers and terminal structures. Electrical characteristics and moisture behavior depend on the named grade; a paper laminate is not a substitute for a heavily loaded canvas part.[3]
Canvas reinforcement suits mechanical components where a coarse cotton fabric provides a supporting laminate. Norplex NP310 is a specific canvas machining-grade reference, not the definition of every brown sheet.[2] [1]
A finer cloth supports smaller machined details and a finer exposed fabric pattern. The exact L or LE grade still controls the applicable electrical and mechanical properties.[3]
Graphite- or other wear-modified products are distinct formulations. Some graphite grades are electrically conductive, so a wear improvement cannot be assumed compatible with an insulation requirement.


Lengthwise and crosswise laminate values differ. The blank layout can rotate a loaded feature relative to the reinforcement; that matters even when the final outline is unchanged. G10 and FR4 are glass-epoxy laminates and have their own material page.[1] [3]
NP310 is used below as a named canvas reference. Its test direction and specimen thickness are retained rather than generalized to paper or linen grades.
| Property | Reference value | Test basis | Specimen or direction |
|---|---|---|---|
| Specific gravity | 1.37 | ASTM D792 | 0.500 in tested thickness |
| Rockwell hardness | M100 | ASTM D785 | 0.250 in build-up |
| Flexural strength | 124.1 / 117.2 MPa | ASTM D790; Condition A | LW / CW; 0.0625 in |
| Flexural modulus | 11.0 / 10.3 GPa | ASTM D790; Condition A | LW / CW; 0.0625 in |
| Tensile strength | 82.7 / 66.9 MPa | ASTM D638; Condition A | LW / CW; 0.125 in |
| Compressive strength | 234.4 MPa | ASTM D695; Condition A | Flatwise; 0.500 in |
| Shear strength | 96.5 MPa | ASTM D732; Condition A | Perpendicular; 0.0625 in |
Norplex-Micarta NP310 TDB, 14 July 2022. LW/CW are lengthwise/crosswise. These typical canvas-grade values and tested thicknesses do not apply automatically to paper, linen or a different laminate product.
Backing beneath the hole limits unsupported layers as the drill exits. The finished exit edge is checked as well as the hole diameter.
A slot beside an outside edge can leave a fragile web. Cutter access and cut direction need to protect that retained feature, especially at a fabric-layer boundary.
The tube wall or sheet direction remains relevant after turning. A finished sleeve is selected and inspected as a laminate component, rather than as an isotropic plastic ring.[4]
The specified reinforcement, orientation and conditioning accompany the dimensional result.
| Feature | Requirement or reference | Accepted condition | Verification |
|---|---|---|---|
| Sleeve bore | Drawing fit and layer orientation | Loose or specified installed state | Bore check in defined setup |
| Terminal support | Hole pattern and electrical path geometry | Specified conditioning | Datum-based geometry check |
| Wear land | Working height and contact profile | At mounting references | Profile/thickness measurement |
| Drilled or milled edge | Drawing chip and delamination criteria | After edge finishing | Critical-edge examination |
The drawing identifies the laminate direction and required condition. Assembled load capacity and an insulation rating are established on the assembly, in the laminate direction and condition the drawing specifies.
A bush bore, a mounting face and a terminal opening have different reference surfaces. We quote their drawing relationships and the stated inspection condition.
A countersink removes laminate around the screw. Its remaining section and distance from the edge need to carry the clamping load without splitting the layers.
A small corner radius concentrates load in a brittle laminate. A compatible radius or local relief can clear the mating part without extending a crack-sensitive notch.
Machining exposes reinforcement at the edge. The electrical path depends on geometry, contamination and the selected grade; a bulk dielectric value does not define that entire path.[4]
Retain the mounting pattern but recover the intended working height from the assembly definition. Copying a worn pad’s thickness can reproduce the lost clearance.
A wear strip needs fastening below the running path and a supported contact face. A lubricated laminate and an insulating laminate may require different formulations.
A support holds the conductor arrangement away from its frame. Slots and standoffs can extend the surface path, but the assembled electrical requirement remains separately defined.
A nest can separate a workpiece from a metal fixture. The useful contact is at the locating lands; copying every surface can make loading and removal harder.
A roller or spacer transfers force through its bore and end faces. The reinforcement layout and local wall matter more than the outer profile’s appearance alone.
Exposed weave is normal for a laminate. The required surface is defined by its contact task rather than by a promise of a metal-like polished appearance.
The exit edge is inspected for chips or separated layers. Enlarging an edge break to hide damage can remove material needed beneath a washer or insert.
A contact face retains its specified geometry after sanding or other finishing. Finish selection does not turn a standard laminate into a self-lubricating product.
Loose machining dust is removed from holes and recesses to the agreed delivery condition. Parts are packed so an exposed edge is not struck by adjacent hardware.
The record distinguishes paper, cotton cloth and glass-epoxy material. Color alone cannot identify a grade or establish its electrical properties.
Hole position and slot width are checked together with retained edge condition. A dimensionally correct hole can still have breakout that affects the fastening surface.
Dielectric endurance and sliding life are established by tests scoped to the actual grade, conditioning and assembly duty. Those tests need the actual grade, conditioning and assembly duty in their acceptance scope.
A specified linen or wear-modified product can cost differently from canvas sheet. Orienting parts to the reinforcement can also change how many fit in a blank.
Narrow tongues, deep counterbores and closely spaced holes leave less supported material. Protecting them can require backing and additional finishing passes.
Checking every critical exit edge or conditioning parts before measurement adds identifiable work beyond cutting the outline.
Identical parts share programming and nesting preparation. Variants that change layer direction or hole patterns keep their own material layout and checking requirements.
The first part checks the actual fastening, sliding or installation task. That result identifies whether the released geometry needs changing.
The trial uses the intended resin/reinforcement and orientation. A different brown laminate is not an equivalent test material simply because it machines to the same outline.
The approved revision records material direction and working features. Those choices carry into the production cutting layout.
Repeat pads and sleeves retain their accepted contact height and orientation. A material-source or conditioning change is identified before replacements are installed.
No. It describes indentation hardness under the stated test basis. ASTM D785 explains that its result is not generally a measure of abrasion or wear resistance. A phenolic roller, washer or sliding part needs its wear assessment tied to the actual contact, mating material, load, movement and lubrication rather than inferred from the M100 number.
No. CE and LE identify electrical grades in the canvas and linen families; the suffix is not a general flame-retardant designation. Any flame requirement needs its own listed material classification and applicable thickness, rather than an inference from the E.
Not as an unchecked substitution. A tube and a sleeve turned across plate can place reinforcement differently around the bore and radial load. That changes which laminate direction supports the contact, so the required orientation and product properties must support the replacement.
Not necessarily. Sheet has manufacturing thickness tolerances, which differ by grade and nominal size. A spacer needing a closer final thickness may require machining allowance and finished faces; specifying only nominal sheet thickness does not define that result.
No. It identifies material requirements within its scope. The finished part’s geometry, machining condition and the assembly’s electrical or mechanical qualification remain separate.
A paper grade intended for warm or hot punching can suit a simple repeated outline when thickness and tooling justify that route. CNC machining remains useful for smaller runs, three-dimensional features or a grade unsuitable for that punching method. The process choice follows the actual laminate and geometry.
Send the drawing, named phenolic grade, stock form, reinforcement direction and quantity. Include the working contact, conditioning and any electrical or wear acceptance that accompanies dimensional inspection.
Named laminate data, reinforcement identities and the acceptance distinctions behind the machined component.
We use Google Analytics to see how this site is used. Analytics cookies are set only if you accept. Privacy Policy